Sudah saya tambahkan sumbernya http://www.printersiam.com/data/DOWNLOAD.HTM Canon BJC-2000 BJC-2100 Series
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel, Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
++++++++++
Canon GENERIC “S” SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer’s carriage will “reset” or move momentarily. If the above was properly performed the printer will enter the “Service Mode”.
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM – Info printout.
3. EEPROM – Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!) After selecting the desired mode (eg 4), press the POWER button to “set” the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
+++++++++++
Canon PIXMA iP1000
Waste Ink Counter Reset Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
+++++++++++++
Canon PIXMA iP1500
Waste Ink Counter Reset. Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green
6. Release both buttons
++++++++++
Canon i320, i255
Waste Ink Counter Reset.
Step 1 : Manual Temporary
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual Temporary
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
step 2 : Software for Permanant
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark “After service mode Pls use software for permanent reset”
++++++++++
Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses – light color – function
Number of presses – light color – function
0 presses – green – Test print (or exit service mode on i960)
1 press – orange – EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses – green – EEPROM initialize
3 presses – orange – Reset waste ink counter
++++++++++
Canon S450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three times. The indicator should be orange.
7: Press Power to set data
++++++++++
Canon BJC 1000 Series
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
++++++++++
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
Unplug Power Cord
Hold POWER and RESUME buttons
Plug in Power Cord
Release buttons
Open front door of printer
Hold the CARTRIDGE and RESUME buttons
Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME
++++++++++
Canon BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
++++++++++
Canon BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
++++++++++
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three times. The indicator should be orange.
6: Press Power to set data
++++++++++
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
++++++++++
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beep
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
++++++++++
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer
++++++++++
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta
++++++++++
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950,
PIXMA IP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
+++++++++
Canon S900, S820, S750, S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button. Pressing the RESUME key will select a function; for example, pressing
RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.
++++++++++
Canon S9000
Turn off printer
Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Press Resume button 2 times then let BOTH buttons go. Green lights will flash and then stop blinking. When green lights are solid, press the Resume button 4 times. Press the Power button and the printer should turn off, if not, press
the Power button once more. Your printer should respond as normal.
+++++++++
Canon MPC190
Reset Waste Ink
1) Enter SERVICE MODE. By pressing Menu Copy Scan Copy Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.
wwwwwwooooooooooooowwwwwwwwwwwwwww gue gax ngerti kata2 loe brow
gimana cara ngisi ulang cartige iP 1880,..tolong..!!!
salam kenal..printerku canon i320, keluar kertas tapi blank trus lampu resetnya kedap kedip warna oranye… kenapa ya?:-? apa ada software untuk atasi mslh tersebut ya..help..help.. tengkyu..:((
Mas nanya donk, untuk printer yang bisa fax yang paling asyik dipake apa yah??
budget 1.5
Tx before
Permisii.. Mas Sy Mau Nanya Printer Canon Ip1980, dll Bisa ngak digunakan satu catridge, seperti contohnya printer HP, mohon Petunjuknya, Maskasi..
saya punya canon mp145 error 27, macamana mau reset. saya dah cuba manual reset tapi tak jadi. mptool v 0.9.2 tak boleh guna amacam ya! tolong.
Saya punya ip 1880, bila saya mau printing selalu ad tampilan spt ini (An ink catridge is not installed properly. Open the printer’s cover, make sure the ink catridge is installed properly, and close the cover.) dan lampu selalu bling 7 x warna kuning dan 1 x warna hijau. mohon sangat petunjuknya. terima kasih
mas.. mo tanya dunk gimana ya cara pakai ip tool 1200 yng bner? soalnya saya coba pakai di printer statusnya indikator ing nya mau penuh. tp begitu printer di start ulang ehh balik lgi ke nol. Klo boleh bilangin langkah demi langkah donk…
OM BISA BANTU ENGGAK , SAYA BELI PRINTER CANON >
MX 308 , GIMANA CARA RESET TINTANYA ( INK LEVEL)
TRUS BISA ENGGAK PRINTER TSB DI PASANG INFUS
kalau memperbaiki printer IP 1200 dengan pesan an ink cartridge is not installed properly gimana ya?? trims
kalau bisa kirim ke email saya ya.. trims
maz kasih tau dong cara memperbaiki katrid canon pixma ip 1980 kalau di pakek untuk ngeprin gk keluar tulisan (katrid yang warna hitam)
mas tolong dong aku punya print hp deskjet3920 ngeblik terus, di comp kedeteknya offline ge ready, kenapa ya mas
mas aku punya permasalahan. tolong bantu aku donk, printer canon 1880 aku kertasnya g’ mau masuk tapi g’ kalo tak pakai ngeprint, tapi kalo saya nyalakan pertama kali printer ku pasti ngeblik tapi kalo dah tak reset dah g’ lagi, kalo mau dipake ngeprint bisa pas mw abil kertasnya gigi-giginya cuma berputar doank trus g’ mw ambil kertasnya habis itu ngeblink?? gimana mas? tolong donk kasih solusinya….
riseternya canon ip3500
Bang sy butuh bantuan neh.
Printer Canon pixma MP145 erorr. Kode errornya E15
serta color ink kedip2 bersamaan dgn kode erorr serta lampu alarm nyala.
Mohon Bantuannya. Trimakasih.
mas2 / ibuk tolong saya dunk
saya pnya masalah ma printer saya……
kok tintanya gak bisa ditambah dgn cara disuntikan..????????
printer saya cannon pixma iP3500….
tolooooooong saya please……..
sebelumnya trims atas saran dan bantuannya.
saya minta tolong….. waktu saya isi ulang tinta hitam pada canon ip3500 malah lampunya kedip – kedip. bagaimana solusinya. terima kasih
TOLONG ADA YG PY RESETER CANON IP3500 PY AKU LAMPUNYA KEDIP2 TERUS WALAUPUN UDAH SY RESET SETELAH DIHIDUPIN LG TRU NGE PRINT MUNCUL SERVICE EROR 9000
HELP YG PY SOLUSI TLNG KIRIMI DI EMAIL KU YAH
THANKS FOR ALL
Saya minta tolong, printer canon ip1700, kan sudah terpsang cartriedge nya sudah terpasang, setelah diisi, tapi ga bisa ngeprint, statusnya tetap aja cartriedge belum terpasang,
Tolongin donk mas,,,,
Asslmkum… tolong dong, printer hp 3920 aku lampu powernya berkedip terus…dan status di propertisnya offline padahal udah dinyalain… kenapa dan bagaimana solusinya ya…?? yang punya solusi masalahku bisa kirim ke email ku…. trims sebelumnya…. wasslam….
minta tulung donk……kalo setting pake tinta hitamnya saja pada printer canon ip 1880 pada linux(opensuse 10.3) gimana ya????, biasanya kan pada settingan configure itu banyak pilihan…….tapi ini cuma ada pilihan RGB doank..ada yang bisa bantu saya???? tulung yo..please
prin canon Ip980 saya macet apa yang harus saya lakukan
printer ix 4000 saya blinking;gimana cara mengatasinya tolong kasih tau solusinya,klo ada minta tolong situsnya apa
helo guys im from philippines, ive looking for someone, to help me with my printer model canon mp198..it needs to reset its waste tank, but nobody knows how, even the canon center here in our place…could someone plss help me to reset my printer..it would be nice if u can send @ my e add richard_ski3@yahoo.com the instruction or procedures on how to reset the mp198. hoping for ur answer guys….tnx n advance
mas bisa kasi tau cara ngreset canon mx300 yang muncul pesan 5800 atas bantuaya terima kasih banyak
bisa gak printer canon pake catridge cuma satu aja? makasih sbelumnya
@andi plecur: gak bisa mas… harus 2-2 nya…
SAYA MEMPUNYAI PRINTER CANON IP3500. PADA WAKTU ITU TINTA HITAM HABIS, JADI SAYA INGIN ISI SETELAH DI ISI MALAH BOCOR, SETELAH DI PASANG TERNYATA LAMPU ORANGENYA KEDIP – KEDIP… GIMANA DONG BANTUANNYA YAA.. YAA. MAKASIH., SAYA SANGAT BERHARAP BANTUAN TEMAN – TEMAN SEMUA
tlg dong cara scan printer hp deskjet F300,trim
please help me with my MP198 limbah tinta tank penuh
thanks ..
INFO DETIL KHUSUS RESET PIXMA
http://thetopsecret.wordpress.com/2009/07/15/reseter-cannon-ip-1880-ip1900-ip/
bagi teman2 yang punyai resetor ip1880 tolong krim ke lemabang_crew@yahoo.com kasih yaaa..
need help printer error mp198 canon error 27 what should i do can be reset????
pls email me about how to reset canon mp198 ink absorber full Bernardinoyoko@yahoo.com
tolong donk bagi siapa yang punya resetter canon IP100 sama MP545 bisa dibagikan ke aku….
printer q uda blink smw
tolong ya……:d:d:d
klo bisa kirim ke alamat email ary_capriconus@yahoo.com
makasih ya sebelumnya……
ada app tuk nge restart printer canon iP 1890???
bantu dong!!!
saya punya printer canon ip3680 minta di reset ulang,ada program untuk meresetnya pleassssse……
2 hari ini pusing bukan maen, 4 printer kantor canon macet bareng, ip1300,1700,1880,1980
yang 1300 and 1700 ngeblink,ngeluarin pesan gini
“an ink cartridge is not installed properly……….”
yang intinya cartridge tidak dipasang sempurna, diminta membuka cover printer dan memastikan bahwa cartridge terinstall sempurna,
udah sy coba berulang kali,tapi tetep nihil,sy reset pake manual and iptool software juga udah tapi tetep nihil(termasuk ngembalikan settingan EEPROM),
bdw,apa beneran cartridgenya yg rusak???ga didetect ma printer???terus cara benerinnya gmn??
problem kedua 1880,1980
rollernya/atau mungkin karetnya bermasalah, setiap kali ngeprint,kertas yang masuk mesti macet di tengah,dan ga stabil sama sekali,kalopun keluar hasilnya acak2an
pengen sih bisa mbongkar, tapi ga tau caranya,tolong donk dibantuin cara mbongkar printer….
sebelumnya tak lupa terimakasih atas semua jawaban yang diberikan
haloo…!!
2 the point aja…!!
aku punya printer IX4000, lampu indikator yang kuning kedip – kedip sbanyak 13 kali…!! dan printernya tidak bisa dipakai..!!
tolong gimana jalan kluarnya, biar bisa normal lagi, cz tu printer dipake GAWE…!!
mohon jawabannya..!!
mas…tolongin aku donk…………
printerku ip1200 blinking 7x orange..udh paku reset manual gak bisa juga..apalagi pake software malah hang (not responding)..udah bingung nih:-w[-(…mohon bantuannya ya mas…dimana sebenarnya yg salah..?? apa mungkin cartrigde warnanya udh rusak ya..?? klo pasang yg hitam aja apa memang gak bisa..?? please..help me…!!!????
Salam, halo pak kurniawan..
saya miftah di bandung..saya punya masalah dengan printer canon ip 1880, masalahnya printer tiba-tiba mati total (tidak bisa power up), trus saya menduga adptor nya rusak (ac pln naik turun), saya coba dengan adaptor canon yang lain eh…berhasil printer kembali normal, namun setelah beberapa jam printer saya matikan dan saya coba hidupkan kembali, ternyata printernya gak hidup lagi alias mati total lagi…(apa adaptornya rusak lagi????).
Mohon bantuannya pak. trims.
miftah.
Ada yang tau cara reset canon ip3300 ga?
klo ada tolongin dong
printer ga bs print lg, pesan errornya :
” the ink absorber full”
thx b4
e-mail : batubara_chuu@yahoo.co.id
aq da masalah dg printer canon MP145, identifikasi errornya “service error 5100″ da solusi ga??
please help , thak’s!
Printer saya MP145 E15 kadang saya reset bisa. tapi kadang keluar lagi E15. Gmana resetnya supaya ga usah ganti catridge??????????
mas kurniawan, printer saya ip1980. hasil print-an tdk mengeluarkan cetakannya sama sekali, yg keluar kertas kosong aja. pdhl tinta sudah saya isi berulang kali…memang printer 1 bulan ini jarang saya gunakan. apa cartdidge-nya kering ya??
mohon bantuannya mas..
ku mau buang mx 308 punya ku yang rewel gak nentu,,, jengkel niannn…. rasanya pengen di terjang depan belakang tu printer biar ancur sekalian… kalo ada yang mau tolongin gua… eror 5B00 terus ada lagi ni… printer canon i6500 asli bikin gua jengkel… sengit tenan aku… rencana mau gua bakar…. kalo ada yang mau baikan ma gua… tlong gua ya… balas ke sini gih_28@yahoo.co.id
duh mas.. .tolong aku dung…
ribet nian iki. lha wong aku di uber2 karo wong2 POLRES…mereka buat apa ni gak tau bikin ribet aja… trus banyak juga gawean yang mau di print… sengit aku… tolong yo bos… eror 5100 lalu di bagusin bisa ngeprint 4 lembar doang trus ganti baju jadi eror 5B00…. weh…weleh… ribettt…. thankyou buat yang mau tolong aku… i love you fulll… hahahahahahahah…….
SELAMAT BERPUSING RIA BERSAMA ANEKA PROBLEM PRINTER SE INDONESA… SEMOGA BAHAGIA DUNIA AHERAT…. PISS.. MAJU TERUS PRINTER INDONESIAN LOVERS
pa Iwan….aku punya ip 3500, setelah tinta asli habis saya coba refill ketempat refill dengan pernyataan sudah direset katanya, tetapi waktu dipasangkan dan dipakai printer ngeblink,sudah digini digitu printer tetap pada pendirianya, akhirnya saya beli tinta asli dengan harga lumayan berat, tangki satunya aja 160.000 kali 4 setelah dipasangkan printer dengan senang hati bekerja dgn baik, ,…mohon bantuan dan solusi biar refil bisa jadi alternatif yang ekonomis….makasih berat.
??????????MP198??????????!
??????????MP198???????,pdedu@sina.com
??!